Last updated November 18, 2026
ADU Warning Signs: A Henderson Homeowner’s Reference Guide
A hairline crack running 45 degrees from a window corner in a stucco ADU in Henderson is almost always a shrinkage crack – cosmetic, inexpensive to seal. A horizontal crack at the same height on both sides of a door opening is a structural load path problem that no amount of caulk resolves. The difference is $200 versus $12,000, and they look nearly identical to a non-specialist. This guide is built around the failure modes we actually see in Henderson – sun-baked roofing, undersized cooling for desert heat loads, wiring added after the final inspection – plus the crack patterns, plumbing timelines, and permit paper trail that tell you what you’re really looking at.
Quick Answer
The warning signs that matter most on a Henderson ADU are not the general ones. They’re UV-degraded roofing sealant, HVAC systems that were sized for a milder climate and now run short-cycling in July, unpermitted electrical added after the original final inspection, hard-water scale building up at shutoff valves, and permit records that don’t match what’s standing on the slab. If a crack runs horizontally, if a panel has mismatched wire gauges, or if Henderson’s permit history doesn’t show a final sign-off, get a professional opinion before you buy, sell, or remodel around that structure.
Table of Contents
- Crack Patterns in Henderson Stucco: What’s Cosmetic and What Isn’t
- HVAC Warning Signs in Desert Heat
- Electrical Red Flags That Point to Post-Permit Additions
- Plumbing Warnings in Henderson’s Hard Water
- Permit Status Red Flags on an Existing ADU
- Roof and Envelope: The UV Problem
- When to Call a Professional
Crack Patterns in Henderson Stucco: What’s Cosmetic and What Isn’t
Most of Henderson sits on expansive desert soils, and most ADUs here are finished in three-coat stucco. Both of those facts shape how a wall cracks. A stucco skin over wood framing will always move a little as it cures, as the soil swells and shrinks with irrigation cycles, and as the afternoon sun heats one face of the building 40 degrees hotter than the shaded side.
Here’s how to read the pattern:
- Diagonal crack from a window or door corner, hairline width (under 1/16 inch): Almost always shrinkage. Seal it and note it. Recheck in a year.
- Vertical crack along a framing joint or a stucco control joint: Normal movement. Cosmetic.
- Horizontal crack across a door or window opening, on both sides, at the same height: This is a load path problem. Something above the opening is transferring weight sideways, or the header is undersized. Needs engineering review.
- Stair-step crack following mortar joints in any brick veneer: Foundation movement or differential settlement. Needs evaluation.
- Crack wider than 1/8 inch, any orientation, that has grown since you last looked: Active movement. Get it looked at now, not next season.
The reason the 45-degree shrinkage crack and the horizontal load-path crack get confused is that from six feet away they can look the same. The tell is direction and symmetry. A shrinkage crack radiates diagonally from a corner and appears on one face. A structural crack runs level and typically shows up on both sides of the opening. If you’re unsure, that’s exactly what a documented inspection is for. If your ADU is a conversion rather than a new build, the same rules apply but with one difference: the original garage slab may have been poured to a shallower thickness than a purpose-built foundation, which changes how the walls above it move.
HVAC Warning Signs in Desert Heat
An ADU cooling system in Henderson runs under a load that a designer in a milder climate would never size for. Design-day temperatures here push past 110°F, and an undersized system doesn’t fail dramatically – it just degrades quietly for three summers until it can’t hold the set point.
What to watch for:
- Short cycling. The unit runs for five minutes, stops, and starts again. In an oversized or refrigerant-starved system this becomes the normal pattern. It costs you money and wears the compressor.
- Refrigerant pressure drop symptoms. Warm air from the vents, ice on the indoor coil, or a system that cools well in the morning and can’t keep up by 3pm. A licensed tech measures superheat and subcooling – a homeowner can’t diagnose this by feel.
- Condenser coil fouling. Henderson’s blowing dust and spring pollen pack into the outdoor coil fins. A fouled coil can’t reject heat, so the system runs longer and hotter. Visible matted debris between the fins is a warning sign, not a cleaning reminder.
- Refrigerant line insulation cracked and sun-bleached. UV destroys the foam on exterior line sets within a few years. Bare copper line loses efficiency and eventually corrodes.
- Air handler in an unconditioned space. We see this often in garage conversions. An air handler in a 130°F attic or garage is fighting itself.
If the ADU was built as a garage conversion in Henderson, the original garage was never designed to be cooled. Ductwork added later is frequently undersized for the room’s heat gain, and the return path is often just a transfer grille. That’s fixable, but it’s a design question, not a filter change. The right question at inspection is whether the Manual J load calculation was ever done for the space as conditioned square footage – if it wasn’t, the equipment size is a guess.
Electrical Red Flags That Point to Post-Permit Additions
An ADU in Henderson that passed its final inspection in, say, 2019 can still have unpermitted electrical work done in 2023. That work is invisible on the permit record but shows up at the panel. These are the patterns a licensed electrician reads in minutes.
- Mismatched wire gauge at the panel. A 20-amp breaker feeding a circuit wired in 14-gauge cable is a fire hazard, and it’s a sure sign someone added the circuit without a load calculation or an inspection. Look at the breaker ratings against the wire ampacity – they should match.
- Ungrounded outlets in a post-2000 structure. Any ADU permitted in Henderson since roughly 2000 should have grounded receptacles throughout. Two-prong outlets, or three-prong outlets fed by two-wire cable with no ground, mean someone swapped the receptacles without running the wire. That’s a code violation and a shock hazard.
- Double-tapped breakers. Two hot wires under one terminal. Sometimes allowed by the panel manufacturer, usually not.
- Romex stapled to the stucco exterior or run through the attic in direct sun contact. Improvised routing, almost always unpermitted.
- No AFCI or GFCI protection where the current code requires it. Bedroom circuits and outdoor receptacles in Henderson need arc-fault or ground-fault protection depending on the circuit. If the panel shows none on circuits that clearly serve those rooms, the work predates or bypassed inspection.
The way to settle it is not guesswork. A licensed electrician does a 30-minute panel and circuit walk, documents what they find with photos, and notes the specific circuits involved. That documentation is what a seller needs to disclose and what a buyer needs to price the remediation. Do not open a panel cover yourself – that’s genuinely dangerous, and the interior is a live-current space even with the main breaker off.
Plumbing Warnings in Henderson’s Hard Water
Henderson’s municipal water runs hard, and hard water leaves a record on your ADU’s plumbing that tells you its age and condition better than a home inspector’s summary. The warning signs aren’t drips – they’re deposits and timelines.
Scale at shutoff valves. A white crust ring around the packing nut or the valve handle is calcium buildup. It’s harmless at first, but it means the valve is stiffening. A stiff shutoff valve that hasn’t been turned in years will often fail open when you need it closed during an emergency. Exercise the valves once a year; replace the ones that won’t turn.
Water heater anode depletion. The sacrificial anode rod inside a tank water heater is there to rust instead of the tank. In Henderson’s water chemistry, that anode typically depletes in three to five years, well before the tank itself fails. Once the rod is gone, the tank starts rusting from the inside and you get a slow leak from the bottom of the tank, months before the tank lets go. If the water heater is more than five years old and the anode has never been checked, that’s a warning sign worth acting on. Tankless units have a different timeline – scale builds on the heat exchanger and needs periodic flushing.
Pressure regulator failure. Henderson’s delivery pressure varies by neighborhood, but anywhere the street pressure runs high, a failing pressure regulator pushes the whole ADU’s plumbing toward pinhole leaks and fixture failures. A pressure reading above 80 psi at a hose bib is a sign the regulator needs replacing.
Corrosion at dissimilar-metal joints. A copper fitting screwed directly onto a galvanized nipple will corrode at the joint. The tell is green or white crust at the connection. That’s a slow leak waiting to happen and worth documenting before you finish the walls around it.
Permit Status Red Flags on an Existing ADU
This is the one that catches buyers in Henderson most often. An existing ADU that looks solid can be entirely unpermitted, or partially permitted – the shell passed but the final wasn’t signed off. Both scenarios affect financing, insurance, and resale.
You can pull the permit history in about ten minutes, and you don’t need to be an owner to do it:
- Go to the City of Henderson’s online permit portal. Search by the parcel number, not the street address. Parcel numbers are stable; addresses get reformatted.
- Look for two permits. A permitted ADU usually has a building permit and a separate trade permit set for electrical, plumbing, and mechanical. If you see the building permit but no trade finals, the trades were likely done without inspection.
- Check the final inspection date. A permit with a final sign-off is closed. A permit with no final is still open, which means the structure was never signed off as complete – even if it’s been standing for a decade.
- Compare square footage. The permitted square footage on the building permit should match the square footage you’d measure on site. A mismatch of more than a few percent means the structure was enlarged after permitting.
- Look for a certificate of occupancy or final approval letter. If it’s missing, ask the seller why. The answer is usually a story you want to hear before you write an offer.
- Search the address for any expired permits. An expired permit is often a project that stalled and was finished by someone else later – which means the finished work was never inspected.
If the records don’t line up, you’re looking at one of two paths: legalize the structure through a permit process, or price the risk into the deal. The first path is what our ADU Design & Permitting in Henderson service handles; the second is a conversation with your agent. Either way, the record is what it is, and no amount of asking nicely changes what’s in the file.
Roof and Envelope: The UV Problem
Henderson’s sun does specific, predictable damage to a roof, and the tell is not a leak – it’s the state of the sealant and the underlayment before the leak starts. Roofing sealant, whether it’s the mastic around a vent boot or the sealant on a fascia termination, degrades in this climate in roughly half the time it lasts in a milder one. Check the roof at the penetrations first – plumbing vents, exhaust fans, skylights. A cracked or chalky sealant at a vent boot is a warning sign well before it fails.
On flat or low-slope roofs over a converted garage, the membrane is the whole story. A membrane that’s pulled away from the parapet, has a “fishmouth” wrinkle at the edge, or shows blistering is moving. Sealing it each year is a bandaid, not a fix. If the roof is over ten years old in Henderson, the underlayment is past its design life, and the next step is replacement, not another layer of coating. If your ADU was built from a prefab or modular system, coordinating the roofing and enclosure details with the original manufacturer’s specification is how you avoid voiding any warranty the system came with – the enclosure system and the roof are a package, and mixing them is a common mistake.
Stucco exterior finish is the other envelope issue. In Henderson, stucco is typically finished with an elastomeric coating that does the UV-blocking work for the wall. If the coating has chalked and faded to a dead flat white, it’s no longer doing that job, and the stucco behind it will start pulling water. If you’re building new, the finish specification matters as much as the framing – if you’re weighing options, see our New Detached ADU in Henderson page for how we specify enclosure.
Common Mistakes to Avoid
- Caulking a horizontal crack and calling it fixed. Caulk is fine over a shrinkage crack. Over a structural load-path crack, it hides the problem and it comes back. Get the pattern evaluated first.
- Assuming a clean permit record means the ADU is legal. A closed building permit in Henderson doesn’t guarantee the trades were inspected. Check the trade finals and the certificate of occupancy separately.
- Trusting a home inspection to catch ADU-specific problems. A general inspector is looking at the main house, not the specific failure modes of an ADU – the undercooled air handler, the post-permit electrical, the missing final inspection.
- Ignoring an aging water heater anode. The cheapest maintenance item on the whole ADU prevents the most expensive plumbing repair. If the anode was never checked, it’s depleted in Henderson’s water within a handful of years.
- Sizing HVAC equipment by rule of thumb. A “one ton per 500 square feet” shortcut is not a Manual J load calculation, and in a Henderson ADU it produces a system that runs wrong for its entire life.
- Skipping the condenser coil cleaning. Henderson’s dust and pollen mat the outdoor coil over a season. It’s cheap to clean and expensive to ignore in the form of a shortened compressor life.
- Buying an ADU as “extra square footage” without a written scope. Any remediation should be specified and priced in writing before work starts. If a contractor won’t put the scope on paper, that’s the warning sign that matters most.
When to Call a Professional
Call a professional if you see a horizontal crack at a door or window opening, a crack wider than 1/8 inch, or any crack that has grown since your last look. Call if the ADU can’t hold set point on a July afternoon or the condenser coil is visibly matted with dust. Call if the panel shows mismatched wire gauges, double-tapped breakers, or two-prong outlets in a structure built after 2000. Call if the permit record shows an open permit, a missing final, or square footage that doesn’t match. Call if the water heater is past five years and the anode was never checked.
Ellery ADU Studio Henderson offers free estimates in Henderson – call (833) 632-6140. If you already have a written estimate in hand from someone else and want a second read on it, we’ll give you one at no charge and tell you where the scope is thin. Every project we take is priced in writing before any work begins, and you get a documented photo record of what we found and what we did.
Frequently Asked Questions

Direction and symmetry are the tells. A diagonal hairline crack radiating from a window corner is almost always a shrinkage crack and costs a few hundred dollars to seal. A horizontal crack at the same height on both sides of a door opening is a load path problem that needs engineering review. If the crack is wider than 1/8 inch or is growing, treat it as structural until a professional says otherwise. Call (833) 632-6140 for an exact quote on an inspection – estimates are free.
Yes, and it takes about ten minutes. Search the City of Henderson’s online permit portal by parcel number, not address. Look for a building permit, the trade permits for electrical, plumbing, and mechanical, and a final inspection date on each. If a trade permit exists but shows no final inspection, that work was never signed off. A missing or open permit on an existing ADU is a red flag worth addressing before an offer.
The system is likely undersized, low on refrigerant, or fighting a fouled condenser coil. In Henderson’s heat, an undersized unit can’t hold the set point, and a unit with low charge loses capacity as the afternoon heat rises. The first step is a licensed technician measuring superheat, subcooling, and static pressure. That’s a diagnosis, not a guess, and no amount of turning the thermostat down will fix an equipment problem.
The common signs are mismatched wire gauges at the panel, double-tapped breakers, ungrounded outlets in a post-2000 structure, and wiring routed through the attic or across stucco without protection. Any one of these is a strong signal that the circuit was added without a permit or an inspection. An electrician can document the specific circuits and price the remediation. Call (833) 632-6140 to schedule a free estimate.
In Henderson’s hard water, the anode rod typically depletes in three to five years. Once it’s gone, the tank starts rusting from the inside, and you get a slow leak from the bottom months before the tank fails outright. Check or have the anode checked within the first five years. If it’s already depleted, replacement is far cheaper than a tank failure in the middle of summer. Call for a written quote before scheduling.
No, and that’s the point of a written price before work begins. Under Haven Standard Clause 1, every project is quoted in writing before any work starts, and that price governs the job. Scope changes only if you ask for one. If a contractor can’t put the scope and price in writing before starting, that is the single most reliable warning sign in the entire ADU process.
The Bottom Line
The ADU warning signs that cost Henderson homeowners the most money are the ones that don’t look dramatic: a horizontal crack mistaken for a cosmetic one, an HVAC system quietly undersized for desert heat, an unpermitted panel addition that shows up as mismatched wire, a water heater anode that quietly did its job and then was gone. Read the crack pattern before you caulk it. Check the permit record before you buy it. Get the panel and the coil and the anode looked at by a professional with a written scope and a written price. If you’re weighing an ADU project or a purchase, start with a free estimate – call (833) 632-6140.
Written by the team at Ellery ADU Studio Henderson.


