Cover Junior ADU Conversion: The Henderson Owner’s Guide
A Cover junior ADU conversion in Henderson typically runs $18,000-$34,000 installed for the interior conversion scope – framing, electrical, plumbing rough-in, insulation, drywall, finishes, and permit coordination – depending on which Cover shell you’re working from and how the panel or garage bay is currently wired. The “part” here isn’t a single component you swap. It’s the conversion scope Cover’s prefab shell was never finished for, and it fails when an owner discovers the shell was delivered as a shell only and the interior build-out was priced and permitted separately. Most Henderson owners find this out when a lender’s appraisal, an insurance inspection, or a city inspector flags the space as unpermitted or incomplete.

Which Cover Models This Applies To

Cover has shipped its backyard and side-yard shells under a few different configurations, and the junior ADU conversion scope attaches differently depending on which one you own. The two things that determine your conversion path are the shell’s as-built electrical service – whether it came pre-wired for a 60-amp subpanel or landed with a bare 30-amp feed – and the wet-wall location, since Cover places the plumbing stub in a fixed spot per model and a conversion that moves it adds real cost.
To identify what you have, read the data plate inside the door frame (Cover labels each shell with model, serial, and month/year of manufacture) and measure the interior clear span at the floor. Corner-to-corner measurements within 1/4 inch tell you whether your shell is the standard plan dimension or a site-modified one. Those modified units are the ones where aftermarket conversion kits don’t fit and where a documented drawing set matters more than a parts number.
On OEM versus aftermarket: for Cover specifically, the structural shell, envelope, and glazing are proprietary and should stay OEM through Cover’s own replacement channel. The interior conversion – framing, rough electrical, plumbing extensions, finish materials, fixtures – is standard residential work and can be built to spec by any licensed contractor working from the permitted drawings. That’s where a written set of plans beats a parts list, every time. We’re an independent design-build studio and not affiliated with Cover; we specify and coordinate Cover systems within the same single contract as the conversion work, and we do the same for Abodu and Dvele owners who land in a similar spot.
Signs Your Cover Junior ADU Conversion Is Failing
- The space fails a city inspection. Henderson’s building department treats an unconverted shell as storage, not habitable space – if your conversion was never permitted, the inspection write-up will list the electrical, egress, and insulation gaps in order. That list is your scope.
- The 30-amp feed trips when you run a microwave and a space heater together. That’s the shell’s original service limit, not a fault – Cover ships some shells with a feed sized for lighting and outlets only. A conversion needs a load calculation and usually a subpanel upgrade.
- Condensation on the interior walls in summer. Henderson’s desert swing from 105°F days to 75°F nights drives moisture through an uninsulated shell wall. If you’re seeing it, the envelope is incomplete, and finish work over a wet wall will fail within a season.
- The plumbing stub doesn’t line up with where you want the bathroom. Cover fixes the wet-wall location at the factory. A conversion that ignores it pays for a relocated drain line and a re-poured slab patch.
- Your lender or insurer asks for a certificate of occupancy and you don’t have one. This is the most common discovery in Henderson. An unconverted or unpermitted Cover shell appraises as storage, and the gap between that and habitable square footage is the dollar figure that sends owners looking for a fix.
Replacement Cost & What’s Included

In Henderson, the conversion scope typically prices like this:
| Scope | Typical range |
|---|---|
| Permit set and plan review coordination | $2,500-$5,000 |
| Electrical service upgrade and subpanel | $2,000-$4,500 |
| Plumbing extension and fixture rough-in | $2,500-$5,000 |
| Insulation, drywall, and envelope completion | $4,000-$7,500 |
| Kitchenette, bath finishes, flooring, and trim | $5,000-$10,000 |
| Final inspection and certificate of occupancy | included in the above |
What drives your number up or down: the ampacity of the existing feed, whether the wet wall stays put, and how much of the shell’s interior finish was already delivered. Every project gets a written price before any work starts – Haven Standard, Clause 1 – so the range you see here becomes a fixed number on paper, not an estimate that drifts. The work is covered by the 365-Day Done Right Promise: if the finished conversion isn’t built to the permitted drawings, we make it right, in writing, before the project starts.
DIY or Call Us?
You can safely check three things yourself: read the Cover data plate inside the door frame and note the model and manufacture date; measure the interior clear span; and look at the panel to see what amperage the shell’s feed is rated for. That’s information-gathering, and we’ll take it over the phone.
The electrical service upgrade, the plumbing relocation, and anything touching the shell’s weather envelope are not owner work. A subpanel swap done wrong is a fire risk, and a relocated drain line under a slab is a demolition you only want to pay for once. Henderson inspections are strict on both, and a failed inspection costs more than doing it right the first time. Call (833) 632-6140 and we’ll walk your shell through what the conversion actually needs.
FAQs

How long does a Cover junior ADU conversion last? The conversion itself is standard residential construction and holds up for decades if it’s built to code and permitted; the shell’s envelope is the maintenance item in Henderson’s heat, and the sealant joints typically need attention every 5-7 years. Under the 365-Day Done Right Promise, anything we built that isn’t matching the drawings gets fixed within the first year.
Can it be repaired instead of converted? Sometimes. If the shell is sound and the gap is a failed inspection item – a missing GFCI, an undersized feed – that’s a repair, not a conversion, and the price reflects it. If the shell was never finished inside at all, there’s nothing to repair; there’s a scope to build. Call (833) 632-6140 and we’ll tell you which one you’re looking at.
How long does the swap take? A straightforward conversion runs 6-10 weeks from permit approval to final inspection, with most of that time in the city’s plan review rather than on site. We hand you the permit set and a written schedule before work begins.
How do you source the part? For Cover’s proprietary shell components – envelope, glazing, structural elements – we coordinate directly through Cover’s replacement channel so the warranty path stays intact. For the interior conversion, we build to the permitted drawings with materials named in the written scope, and you get a documented photo record of what went in.
Let’s put a real number on your Henderson conversion this week. Call (833) 632-6140 for a free estimate, and bring your shell’s data plate info – we’ll quote it in writing before any work starts.
Written by the team at Ellery ADU Studio Henderson, serving Henderson and nearby areas.












